Drexelbrook’s ThePoint™ Series Point Level Switch: Settings, Adjustments, and Changing Calibration Modes

The AMETEK Drexelbrook ThePoint™ Series uses No-Cal™ technology to detect the presence or absence of material without calibration or initiation via setpoint adjustments, push-buttons or magnets.

ThePoint™ level measurement switch features both Auto-Cal and manual calibration. The standard Auto-Calibration mode is applicable to most liquid and slurry point level measurements. If preferred, the manual calibration can be used and is recommended for some application. ThePoint electronic unit has auto and manual calibration modes built into the standard unit and can be accessed through the simple routine shown in the video below. The inclusion of these calibration modes allows the Drexelbrook RF Point Level Products application flexibility that is far greater than any other point level product on the market. ThePoint™ level switch can be used in Liquids, Solids, Slurries, and Interface applications.

To learn more specific instructions on the (8) calibration modes ThePoint™ has available, download the "Drexelbrook ThePoint Series Point Level Switch Installation and Operating Instructions" from this link.


Piping Specialties / PSI Controls: New England's Preferred Source for Industrial Valves, Valve Automation, and Process Instrumentation

Founded in 1975, with offices in Portland, Maine and Danvers, Massachusetts, PSI has earned their reputation as New England's premier supplier of industrial valves, valve automation, process instrumentation and specialty process equipment.

PSI specializes in engineered products for these industries:

  • Power Generation
  • Pulp & Paper
  • LNG / LPG / Natural Gas / Gas Storage & Distribution
  • Pharmaceutical / BioTech
  • Food and Beverage
  • HVAC
  • Water & Wastewater

Piping Specialties, Inc / PSI Controls
https://psi-team.com
800-223-1468

Top 5 Considerations in Selecting Pressure Gauges

Pressure gauges are ubiquitous in industry and installed on machinery around the world. While there are millions of possible combinations of shapes, sizes, options and materials, careful attention needs to be given to the following five criteria for safe use and long product life.

1) Process Media
Direct exposure of the sensing element to the process media is a possibility, so attention must be given to any corrosive media, media with particulate, or media that can solidify and clog the pressure gauge element. For non-clogging media, a direct connection and Bourdon tube sensor can be applied. For process media that could potentially cause clogging, a diaphragm seal should be used.

2) Process Media Temperature
Gauge with diaphragm seal
Gauge with
diaphragm seal.
(AMETEKUS Gauge)
Very hot media, such as steam or hot water, can elevate the gauge's internal temperature leading to failure or an unsafe condition. For high temperature application, the use of a gauge "siphon" or diaphragm seal be applied.

3) Ambient Operating Temperature and Environment
It is important to know the rated ambient environment for any instrument. Elevated ambient temperatures, moisture, vibration, and corrosive atmospheres can all affect accuracy, calibration, and safety. Choose the proper case and mechanism materials if oxidizing or reducing atmospheres exist, and consider the addition of ancillary devices, such as remote diaphragm seals, to relocate the gauge.

4) Possibility of Severe Pressure Fluctuations
In applications where dramatic line pulsations or strong over-pressure conditions are a possibility the use of pressure restrictors, snubbers, or liquid-filling will extend the service life of the pressure gauge.

5) Mounting
Snubbers & restrictors
Snubbers & restrictors

Pressure gauges are standardly available with bottom (radial) and back connections. NPT (National Pipe Thread Taper) threaded connections are generally the standard. Many other process connections are available though, such as straight threads, metric threads, and specialized fittings. Make sure you know how the gauge is being connected. When mounting, pressure gauges should be almost always be mounted upright.

For more information about pressure gauges, contact PSI Controls by visiting https://psi-team.com or by calling 800-223-1468.

What is an External Spring, Lever & Weight Single Disc Check Valve

Check valve animation
Single disk check valve animation.
According to Wikipedia, "Check valves are used in many fluid systems such as those in chemical and power plants, and in many other industrial processes."

Check valve symbol
Check valve symbol
As shown in the animation to the left, the single disc (swing) check valve use the directional flow to push open a swinging disk. As long as flow continues, the disk stays raised. But as flow stops, gravity allows the disk to re-seat itself and any reverse flow is prevented by the closed disk. As reverse flow pressure increases, the swing check valves seating increases as well.

Single disc check valves also use springs, levers and/or weights mounted on the valve to allow for better control of surge and to prevent the valve from slamming closed. These assemblies are used to vary the valve’s closing operation in order to reduce the severity of the closing water hammer.

spring, level and weight assisted check valve
External spring, external spring & lever, and external spring, level & weight designs (left to right).
Courtesy of Champion Valve.
For more information on any industrial check valve, contact Piping Specialties, Inc. by visiting https://psi-team.com or calling 800-223-1468.

An Introduction to Triple Offset Butterfly Valves

Triple Offset Butterfly Valves
Triple Offset Butterfly Valve
(Pratt Industrial)
Triple offset butterfly valves are designed to fill the demand for an alternate solution to gate valves and ball valves. They are preferred when weight, space, performance, and the ability to modulate to the process flow are an issue. Typically available in sizes 3" through 48", and in 150, 300 and 600 pressure classes, they're rated for operation from -50 deg. F. through 750 deg. F.

Designed with metal-to metal seats, triple offset butterfly valves provide distinct advantages over traditional gate valves, namely lower weight, zero-leakage, ease in automation, and capable of being used for modulating service.

Industries Using 
  • Chemical
  • Refinery
  • Power
  • Steam Generation
  • Petrochemical
  • Water/Waste Water Treatment
Triple Offset Butterfly Valves
Click on image for larger view.
Triple Eccentric Disc-Shaft Design (diagram above)
  • Offset 1: It is accomplished by moving the centerline of the shaft away from the seating plane.
  • Offset 2: It is accomplished by moving the centerline of the shaft offset from the centerline bore of the valve.
    • These two design features cause the disc to open and close relative to the body seat in a “camming” action and effectuate the position seated valve design which is typical of the High Performance Butterfly Valve, however there is still contact between the disc and the seat in the first several degrees of opening and closing which can cause premature wear of the seat in the general areas.
    • In order to achieve an API 598 Shut Off classification a 3rd offset needed to be introduced to make the valve a “torque seated” design with graphite and metal seating surfaces.
  • Offset 3: It is accomplished by adjusting the cone angle created by the 1st and 2nd offset angles at some point downstream of the valve in the center of the piping to the adjacent piping wall as depicted in the illustration below “Sticking tendency”. By incorporating the 3 offsets into one design typical of gate valves is eliminated with seat contact throughout the entire stroke reducing run torques and improving actuator modulating performance at the same time.
For more information, contact Piping Specialties by visiting https://psi-team.com or by calling 800-223-1468.

What is a Piping and Instrumentation Diagram (P&ID)?

Piping and  instrumentation diagrams (P&ID's) are schematic representations of a process control system and used to illustrate the piping system, process flow, installed equipment, and process instrumentation and functional relationships therein. They are also known as "process and control flow diagrams".

They are intended to provide a “picture” of all the process piping, including the physical branches, valves, equipment, instrumentation and interlocks. By using a standard set of internationally recognized symbols, each component of the process system - instruments, piping, motors, pumps - is recognized on paper or computer screen.

P&ID’s may be very detailed and are generally the primary source from where instrument and equipment lists are generated. They are also used as a handy reference for maintenance planning and system upgrades. Furthermore, P&ID’s also play an important early role in plant safety planning by providing a thorough understanding of the operability and relationships of all components in the system.

Watch the short video below for more information.

For more information contact:
Piping Specialties / PSI
https://psi-team.com
800-223-1468

Continuous and Point Level Control Selection Guide

Drexelbrook Continuous and Point Level Control
Drexelbrook Continuous and Point Level Control Products
Based on experience from of thousands of inquiries about level measurement, most questions boil down to "What is the best level measurement instrument for my application? That depends on quite a few application considerations, such as:
  • Will the measured media add coating to the probe?
  • Can the probe have contact with the media?
  • Are there explosion hazards?
  • What is the physical type of application, well, tank, open channel or floating roof tank?
This document can help deliver the perfect continuous level transmitter or level switches for your application.

Download a PDF version of the Drexelbrook Continuous and Point Level Control Selection Guide here, or view the embedded document below.

https://psi-team.com
800-223-1468